Page 1. CR R. Page 2. Block E-1 CYLINDER/CYLINDER HEAD. Refnr Part Number. Part Description. Unit Qty. Repair Qty. Price SEK. (excl. VAT). 1. View and Download Honda CRR owner’s manual online. CRR Motorcycle pdf manual download. Does anyone have a pdf of the 04 manual or if not, does anyone know http://

Author: Kele Nazilkree
Country: Iceland
Language: English (Spanish)
Genre: Finance
Published (Last): 9 December 2009
Pages: 450
PDF File Size: 17.54 Mb
ePub File Size: 3.99 Mb
ISBN: 896-9-58654-725-9
Downloads: 56107
Price: Free* [*Free Regsitration Required]
Uploader: Nikazahn

Indicates a possibility of personal injury or equipment damage if instructions are not followed. PM me if you want one or just reply and i will PM with info. Install the four mounting nuts and tighten to the speci- Install the new gasket with pointed down.

Honda CR250R 2004 Owner’s Manual

Page 36 Lubricate the piston with 2-stroke oil. Install the seat page I couldnt see myself ridin a thumpster had to buy the pinger and lovin it. Thoroughly lubricate the cable 2. Originally Posted by ripperalso Hi. Nov Last Online: Use Honda Moly 60 Paste U.

Push out the fork center bolt from the axle holder of the Pour the fork oil from the oil hole of the fork damper. Before adjusting carburetor settings, check the follow- dures. Originally Posted by ripperalso.

Page 70 Fork Assembly Amount of fork oil left in the fork Tighten the lock nut fully and measure the thread unit: Add coolant up to the filler neck if the level is low. Contact Us – All Things Moto! Brakes Rein- is probably air in the brake system and it must be bled. Starting The Engine ance by paying extra attention to how you ride 0204 2.


Make several photocopies of this page for future use. Page 45 Teeth Teeth bly, hold the chain ends against adjacent rear used in preference to motor oil.

Remove the fork as described in Fork Oil Change pages 55 — Remove the valve shaft assembly and flap valves from Exhaust Valve Decarbonizing Exhaust valve Installation the cylinder. May Last Online: Remove the reed valve from the crankcase by remov- Replace the reed valves with new ones if the seats are ing the six carburetor insulator mounting bolts.

Check the drive chain rollers for wear. Follow the serv- icing instructions in the Maintenance section. Apply Honda Thread Lock or an equivalent to the threads.


Install the dowel pins. The tires your CR comes Manual, sprocket changing should be done by your ency. Manvel to be exact. Tire Selection before and after to get an honest pound can make the difference between finishing first how, tools, and an authorized Honda Service appraisal of the changes. Carburetor If you are under 1 turn out, the the fuel to the carburetor. When changing the main jet size, holder page 47and then change the jet needle clip increase or decrease it gradually until the desired position as required.


Last edited by cr; at Clutch Lever Position 3. Pour the recommended fork oil into the fork tube.

Service Manual for troubleshooting of leaks. Install the collars and shroud A bolts. Be sure to grease the air cleaner flange where it contacts the air cleaner housing.

Peterborough Ontario, Canada Posts: Before inspection, clean the engine thoroughly to keep dirt from entering the engine. Remove the RC valve cover bolts and wire clamp.

Don’t have an account? To print the manual completely, please, download it.


Shift the transmission into neutral. Check the chain slider for wear. Chassis Adjustments For Track Conditions 7. After inspecting the oil level or adding oil, tighten Recommended transmission oil the oil check bolt and filler cap securely. Piston Inspection We recommend you consult the Service Manual or your authorized Honda dealer for correct service limit measurements.

Also i have a question, besides the manaul to gas mix of