CONFIGURATION ROUTAGE STATIQUE CISCO PDF

Les routeurs Cisco et IOS. Configuration de la route par défaut. En mode configuration ip route adrIPReseau masque adrIPGateway route statique. Le pare-feu VPN sans fil N Cisco RVW comprend: la prise en charge du routage statique, versions RIP (Routing Information Protocol) 1 et 2 et du routage. CONFIGURATIONS LINUX Vérifiez que ROUTEUR CISCO IOS: a , ROUTEUR QUAGGA A interface.

Author: Tygokinos Yozshusar
Country: Djibouti
Language: English (Spanish)
Genre: Sex
Published (Last): 6 January 2017
Pages: 126
PDF File Size: 2.84 Mb
ePub File Size: 18.38 Mb
ISBN: 763-2-21062-495-1
Downloads: 50208
Price: Free* [*Free Regsitration Required]
Uploader: Nikojora

Your feedback helps improve this site.

Enterprise-level Cisco routers are configurable using the Cisco IOS command line, rather than a web management interface. Network configurations are not restricted to a single static route per destination: Thank you We appreciate your feedback.

Configure a Static Route

R0 show ip route. To route IP traffic destined for the network TP-Link takes your privacy seriously. No Install —Do not install the route in either route table. Now we consider a real-world example of static routing. The administrative distance can be manually re configured so that the static route can be configured as a backup route, to be used only if the dynamic route is unavailable.

Therefore, foutage you want PC to visit servers in intranet, you have to set up a static route on router2 helps your packet route to router1. If you configure a static route pointing to an exiting interface for example: Because there is no route to server1 and server2 on route table of router2, thus the request will be thrown away.

  ITEXT XFA TO PDF

Powerline Adapter Transforms electrical wiring to carry the network signal.

Static routing – Wikipedia

Click here to contact TP-Link technical support. Network Resources Free Router Simulators. By using this site, you agree to the Terms of Use and Privacy Policy. And RIP has an administrative distance of Premium Membership Become a member to interact with all questions and practice fisco Perform the following task to configure Static Routes or a default route for a virtual router on the firewall.

With dynamic routes, routers can communicate with each other to exchange routing information. IP subnet mask for this address is In most Linux distributions, a static route can be added using the iproute2 command.

Choose this option if you want either unicast or multicast traffic to use the route. Step 4 Click Add New…. Static Route Overview Static Route Overview If you decide that you want specific Layer 3 traffic to take a certain route without participating in IP routing protocols, you Multicast —Install the route in configuratiom multicast route table available configuratiln IPv4 routes only.

Static routing can have some potential disadvantages: Dynamic routes, on the other hand, use a routing protocol to determine the best path fonfiguration the routes can be changed depending on specific parameters like bandwidth, delay, cost…. Please turn it on for the best experience. Well, 1 is the administrative distance AD and 0 is disco metric of that static route. Next VR —Select this option and then select a virtual router if you want to route internally to a different virtual router on the firewall.

  LIBRO DE TRIBU CAMADA DE FENRIS PDF

Directly connected routes have an administrative distance of 0. A static route is a pre-determined path that network information must follow configuratkon reach a specific host or network. The following is typed at a terminal: Click the IP or IPv6 tab to specify the Configure a Static Route. The gateway of PC is router2 which connected the Internet, but when PC visit servers in intranet, firstly the request will be sent to router2.

R1 config ip route Confguration —Install the route in the unicast and multicast route tables available for IPv4 routes only. As the administrator of the network, you are tasked to connect them so that employees in the two LANs can communicate with each other. So there are 2 networks that are directly connected to R0: Find out more or Sign In.

User Application Requirement Updated