IRFP Transistor Datasheet, IRFP Equivalent, PDF Data Sheets. MOSFET. Parameters and Characteristics. Electronic Component Catalog. Fifth Generation HEXFETs from International Rectifier utilize advanced processing techniques to achieve extremely low on-resistance per. THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT IRFP SiHFP ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless.

Author: Moshakar Goktilar
Country: Yemen
Language: English (Spanish)
Genre: Finance
Published (Last): 9 October 2008
Pages: 276
PDF File Size: 13.95 Mb
ePub File Size: 17.41 Mb
ISBN: 178-9-42350-444-7
Downloads: 98986
Price: Free* [*Free Regsitration Required]
Uploader: Moogumuro

The X axis is voltage and you can see it is limited to volts. Also, both instant and average dissipation are limited see SOA graphs which will give you a time- and Vds-dependent current limit if you irfp1500 want to fry it. However, if you apply Vds, and slowly raise Vgs from zero, at some point in will start to conduct and behave like a current source. Yes, it is complete. You can’t apply anything more than about a volt in reverse. Sign up or log in Sign up using Google. The Y axis is current and this is limited to amps i.

IRFP MOSFET N-CH V 41A TOAC Vishay IR datasheet pdf data sheet FREE from

Is It V too? And power dissipation kW. If your pulse was 10 ms then you could withstand volts whilst taking no more than about 2. When Vgs is high enough, then it will enter ohmic mode and meet its RdsON spec. Post as a guest Name. When the FET is fully on, it behaves more or less like a resistor of value RdsON, which is 36 mOhm in this case, so there would be no way to datasjeet volts datasheer it.

Chupacabras 3, 2 11 By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.


Iirfp150 now that the power taken during this much longer pulse is only watts. I’ve learned from you a lot of information.

Andy aka k 10 Michael George 1, 8 34 Irfl150 if the graph showed this detail you would find that the continuous power rating of watts means a continuous current datashset 1. Email Required, but never shown.

Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Data sheets are marketing. This is called “saturation” for a MOSFET, which always ties my brain into knots, since “saturation” for a bipolar is at the other end of the characteristic. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. This is the datasheet of a mosfet and I have two issues: Which pin is gate and which is drain? Alternatively you could withstand volts but at a reduced current of about 90 amps.

datasheet[1].pdf IRFP_百度文库

This is very much defined as a “single pulse” bottom left corner of graph i. From datasheet you can see, that maximal allowed current is 42A, and power dissipation W.

What is the maximum supply voltage or the maximum operating voltage? Lead assignments are on page 8. The current would be amperes. The Vdss voltage is the voltage which the current starts to flow through fet.

When downloading the data sheet from the manufacturer, the typeset error is not present W vs. To the best of my knowlodge, the only thing that is not correct in the datasheet is the way the on-resistance is declared: That’s an instantaneous power of 9 kW. What will happen if you apply V on 0.


I don’t know where drain, source and gate are.

What this tells you is that if you could turn on and off the MOSFET in 10 us you could take amps but with a limited voltage of about 60 volts. See also this on the last page: It’s easy to get into the habit of skipping over the last pages in a datasheet with mechanical and packaging information, it’s understandable dataxheet you missed it. That’s an instantaneous power of 8. Never miss the small print, let alone the footnotes. Some prefer to call this “linear mode”, since this is the mode to use when you want to make a linear amplifier or a source follower with the FET.

As for the pinout, you can irfp1150 on the standard one, ie GDS. Pin irfp1500 is buried within the mechanical drawings. It is determined by the physical construction of the FET. Sign up using Email and Password. You always answer my questions in a very helpful and informative way.

IRFP150 MOSFET. Datasheet pdf. Equivalent

The most important rule about any data sheet is this: Breakdown maximum Vds applies in all modes. See “Source-Drain Ratings and Characteristics” for numbers on page 2. Internal diode would conduct and prevent this. Sign up using Facebook.

If there’s missing data, the datasheet doesn’t contain it.